| 品牌NSK | 型号皆可 |
| 内径8mm | 外径8mm |
| 订货号D0180614 | 旧型号未知 |
| 厚度8mm | 重量8kg |
| 保持架及其材料A外圈引导 | 滚动体列数单列 |
| 滚道类型球面滚道 | 使用特性高速 |
| 密封防尘形式2RS | 滚动体类型滚针 |
| 密封盖双面密封 | 滚动体钢球 |
| 轴承材质不锈轴承钢AISI440(9Cr18) | 精度等级P0 |
| 组配方式DB | 是否跨境货源否 |
| 货号D0180614 |
江苏nsk轴承的稳定性是在计划停机时间内进行的，根据计划停止补救措施。同时，旧的油脂被去除，或者旧的油被挤压通过排气口。在添加新的润滑脂之前擦拭喷嘴。如果轴承箱内没有喷嘴，则应关闭轴承箱盖或端盖，以清除旧润滑脂，并在清洗后加入相同类型的新润滑脂。
the stability of jiangsu nsk bearing is carried out in the planned downtime, and the remedial measures are stopped according to the plan. at the same time, the old grease is removed, or the old oil is squeezed through the exhaust port. wipe the nozzle before adding new grease. if there is no nozzle in the bearing box, the bearing box cover or the end cover should be closed to remove the old grease and add the same type of new grease after cleaning.
应根据计划反映江苏nsk轴承润滑油的油位和油品质量。在正常情况下，异常油位应在设备油窗的1／3-2／3范围内指定。充油方法是油杯，其油位性能仅是充油能力，而skf轴承箱油位置要满足操作要求，油杯可以考虑油的填充位置低于总体积的1/4。
the oil level and oil quality of jiangsu nsk bearing lubricating oil should be reflected according to the plan. under normal circumstances, the abnormal oil level should be specified in the range of 1 / 3-2 / 3 of the equipment oil window. oil filling method is oil cup, its oil position performance is only oil filling capacity, and skf bearing box oil position to meet the operation requirements, oil cup can consider the oil filling position is lower than the total volume of 1/4.
大量的江苏nsk轴承光滑油被用作样品和一种新的光滑油，这可以被认为是停止油测试以确保油通过的问题。如果样品看起来是混浊的，它可以与水混合，通常被称为油乳化。在这一点上，应该用光滑的油代替。
a large number of jiangsu nsk bearing smooth oil is used as a sample and a new smooth oil, which can be considered as the problem of stopping the oil test to ensure oil passing. if the sample appears to be cloudy, it can be mixed with water, commonly known as oil emulsification. at this point, it should be replaced with smooth oil.
如果江苏nsk轴承样品较深或较厚，则表明光滑油已开始碳化，而旧光滑油应完全停止。如果可能的话，使用新的光滑油来停止油回路。更换润滑油时，必须保证新旧机型的一致性，达到满意的油位。
if the nsk bearing sample in jiangsu is deeper or thicker, it indicates that the smooth oil has begun to carbonization, while the old smooth oil should be completely stopped. if possible, use the new smooth oil to stop the oil circuit. when changing lubricating oil, we must ensure the consistency of new and old models and achieve satisfactory oil level.
使用江苏nsk轴承油浴光滑系统。如果油温是华氏六十度（华氏140度），那么光滑的油就不会被净化，但一年可以更换一次。如果油温为60-100度（华氏140～210华氏度），则需要每年更换4次。如果油温为100-120度（210-250度f），则需要每月更换机油。如果油温度高于120℃（250℃），则必须每周更换一次润滑剂。
use jiangsu nsk bearing oil bath smooth system. if the oil temperature is sixty degrees fahrenheit (140 degrees fahrenheit), smooth oil will not be purified, but it can be replaced once a year. if the oil temperature is 60-100 degrees (fahrenheit 140~210 degrees fahrenheit), it needs to be replaced 4 times a year. if the oil temperature is 100-120 degrees (210-250 degrees f), you need to change the oil every month. if the oil temperature is above 120 c (250 c), lubricant must be changed once a week.
正确安装和维修是江苏nsk轴承异常运行的重要因素。同时，保持清洁度。江苏nsk轴承必须用湿空气清洗和清洗。必须提供准确的设备和光滑度。此外，轴承和塔架的规划、油封状态、平稳状态、变化周期和特殊外观特征都必须附加到张力上。
proper installation and maintenance is an important factor for the abnormal operation of nsk bearings in jiangsu. at the same time, keep clean. nsk bearings in jiangsu must be cleaned and cleaned with wet air. accurate equipment and smoothness must be provided. in addition, the planning of bearing and tower, oil seal state, steady state, changing cycle and special appearance characteristics must be attached to tension.
文章来自：江苏skf轴承 www.wh-skf.com
the article comes from: jiangsu skf bearing www.wh-skf.com
文章来自：江苏ina轴承 www.ina-china.cn
the article comes from: jiangsu ina bearing www.ina-china.cn
文章来自：江苏nsk轴承 www.klbbearings.com
the article comes from: jiangsu nsk bearing www.klbbearings.com
鸿御（上海）国际贸易有限公司
赵先生
13382215187
上海 上海 静安区 虬江路1368弄1号楼