transmitterpanel
①indicator of power input②status ofsignalconnection③hdmiinput
④ir-tx port⑤resetbutton⑥powerinputport⑦ethernet port⑧dipswitch
4 bitsdipswitch:
1~4for 0~15 (group)idselection (such as 0000,0001,0010 etc,)
default tx unicastipaddress is 192.168.168.55 and can be configuredfromwebpage.
tx group ipaddress:239.168.168.1x, where x is the value ofbits[3:0]
receiver panel
①indicator of power input②status ofsignalconnection③hdmioutput
④ir-rx port⑤resetbutton⑥powerinputport⑦ethernet port⑧dipswitch
4 bitsdipswitch:
1~4for 0~15 (group)idselection (such as 0000,0001,0010 etc,)
default tx unicastipaddress is 192.168.168.55 and can be configuredfromwebpage.
tx group ipaddress:239.168.168.1x, where x is the value ofbits[3:0]
user should configurethedip switch within 10 seconds, firmware should reset the system20second after detecting the first change of dip switch, andlatchthe new dip switch value after reset.
how to connect hdmioverip one source to one display function
1. connect one hdmicablebetween the hdmi output port of source device and the hdmiinputport of transmitter unit
2. connect one hdmicablebetween the hdmi input port of display and the hdmi outputport ofreceiver unit.
3. connect one utpcat5eor better cables between the rj45 port of transmitter unit andrj45port of receiver unit.
4. connect the included5vdc power supplies to both transmitter unit andreceiverunit.
5. power on theoutputdevice first and the source second.
1) onetoone
transmitterreceiver
how to connect hdmioverip one source to many display function
1.connect one hdmi cable between the hdmi outputportof source device and the hdmi input port oftransmitterunit
2.connect one cat5e or better cable between therj45port of transmitter and input port of gigabit ethernetswitchhub.
3. connect one cat5eorbetter cable between the output port of each gigabitethernetswitch hub and rj45 port of receiver unit.
5. power on theoutputdevice first and then the source device.
6. use dip switch hassetup on the transmitter side (group id:0001) for eachreceiver.(group id:0001)
how to connect hdmioverip more source to more display function
many sources tomanydisplays function
1. connect one hdmicablebetween the hdmi output port of source device and the hdmiinputport of transmitter unit.
2. connect one hdmicablebetween the hdmi input port of display and the hdmi outputport ofreceiver unit.
3. connect one cat5eorbetter cable between the rj45 of each transmitter unit andrj45port of gigabit ethernet switch hub.
4. connect one cat5eorbetter cable between each rj45 port of gigabit ethernet switchhubto rj45 port of receiver unit. user can select source channelbysetting up dip switch on each transmitter unit. and selectdisplaysource for receiver units via one remote control.
5. use dip switchselectchange sources .
maintenance
clean this unit withasoft, dry cloth. never use alcohol, paint thinner of benzinetoclean this unit.
productservice
1)damage requiring service:the unit should be serviced by qualifiedservicepersonnel if:
(a)the dc power supply cord or ac adaptor hasbeendamaged;
(b)objects or liquids have gotten intotheunit;
(c)the unit has been exposed to rain;
(d)the unit does not operate normally or exhibitsamarked change in performance;
(e)the unit has been dropped or thecabinetdamaged.
2)servicing personnel:do not attempt to service the unit beyondthatdescribed in these operating instructions. refer allotherservicing to authorized servicing personnel.
3)replacement parts:when parts need replacing ensure the servicerusesparts specified by the manufacturer or parts that have thesamecharacteristics as the original parts. unauthorized substitutesmayresult in fire, electric shock, or other hazards.
4)safety check:afterrepairs or service, ask the servicer toperform safety checks toconfirm that the unit is in proper workingcondition.

---

深圳市品为科技有限公司
张孟
13714135023
深圳市龙华大浪华宁西路恒昌荣(星辉)科技园G栋4楼B区