长沙分类信息网-长沙新闻网

长沙喷码机使用注意事项跟维修店

2019-12-8 0:16:55发布6次查看

1、首要事项就是时刻保证喷头系统及山清水秀整机的清洁干燥,注意开关机时的自动清洗程序是否工作正常;定期清洁风扇过滤网;定期清洁电眼;定期检查电源(尽量能使用稳压及断电保持电源)及地线的连接;检查墨水和溶剂的液位,低位时必须按程序及时添加。
3、由于生产原因如果喷码机使用的频率不高,那么请在3~5天内务必开机一次让墨水系统循环半小时。
4、大部分喷码机都具有自动故障诊断功能,甚至伟迪捷喷码机还有实现了根据环境温度和温度变化的墨水参数自动调整无需操作人员手动干预,可通过菜单显示屏幕中的图标,工作状态提示栏或“系统”菜单中的“状态”提示中获得故障信息或应用注意的事项来解决常见的问题。喷码机在运行过程中,可通过“校验”菜单或“诊断屏幕”,观察机器运行的动态参数,从而更能准确的判断机器的运行状态是否正常。
5、喷码机出现任何故障时,应该采用相应的提示或方法立即解决,若一时解决不了,请及时向供应商或当地售后沟通。
6、喷码机使用的是颜料基墨水(如:白墨)估计停机后再使用的时间在五天后,在最后一次关机的时候,按下关机键后,建议用一个清洁的烧杯,盛装100ml左右的清洗液是溶剂,把喷头放入烧杯中。这样做的好处是可以彻底的清洗回收管路。长时间停机,回收管路堵塞的肯能性是的,因为回收管直接裸露在空气中。采用上面的方法,可以彻底清洁回收管路。如果是超过半个月不用甚至有必要做一次喷嘴逆清洗。
7、通常正规厂商生产的一些颜料墨水喷码机,由于颜料基墨水容易沉淀。在关闭喷码机后,切记不要关闭电源。墨路系统会间歇性的启动一次,防止墨水沉淀。另外要检查溶剂箱的液位。如果液位低,建议添加溶剂。如果事先不添加好,墨水浓度容易升高。
产品英文详情介绍
1, the first nozzle system matter is always ensure clean and dry and beautiful machine, automatic washing machine when the program note switch is working properly; regularly clean the fan filter; regular cleaning electric eye; periodically check the power (and the regulator can be used as far as possible off power to maintain power supply) and ground connection; ink and solvent level must be promptly added in low procedures. 3, for production reasons if the frequency of printer use is not high, be sure to turn a half-hour to get ink circulation system in 3 to 5 days. 4, most of the inkjet printer have automatic fault diagnosis function, even videojet inkjet printer also achieved automatically adjusted according to the ambient temperature and temperature changes of ink parameters without operator manual intervention via the menu screen displays icons matters work status indication bar or the system menu in the state prompt information or the failure to obtain the application note to solve common problems. printer during operation, through the check menu or diagnostic screen observed dynamic parameters of the machine is running, thus more accurately determines whether the normal operating state of the machine. 5, when the printer of any failure, should use the appropriate prompt or immediate solutions, if can not be resolved, please communicate to suppliers or local sale. 6, printer using pigment-based inks (eg: white ink) used for estimating the time after shutdown, after five days, at the time of the last shutdown, after pressing the off button, is recommended in a clean beaker containing approximately 100ml the washing liquid is a solvent, the spray head into a beaker. the advantage of this is that the pipeline can be cleaned thoroughly recovered. downtime, pipe clogging recovery property is willing to be because the recovery pipe is directly exposed to the air. with the above method, thoroughly clean the recovery pipe. if more than half do not even need to do a reverse cleaning nozzle. 7, some manufacturers generally regular inkjet pigment ink, since the pigment-based ink easily precipitate. after closing the printer, remember not to turn off the power. intermittently ink system startup time, to prevent settling of the ink. in addition to the solvent tank level check. if the level is low, add the recommended solvent. if you do not add in advance is good, easy to increase ink density.
查看其它相同标签的文章:喷码机喷码机

长沙鼎捷电子设备有限公司
13787274652
qq: shichuanwen520
该用户其它信息

推荐信息

长沙分类信息网-长沙新闻网
关于本站