| 加工定制否 | 品牌BECKHOFF |
| 型号EL3433 | 工作电压24V |
| 输出频率50kHz | 产品认证CE |
el3413
el3413-0120
el3413-0001
el3433
el3602
es3602
el3602-0002
el3602-0010
el3602-0020
el3612
es3612
el3612-0020
el3632
el3632-0020
el3681
es3681
el3681-0020
el3692
el3692-0020
el3702
es3702
el3742
es3742
el3773
el4001
es4001
el4002
es4002
el4004
es4004
el4008
es4008
el4011
es4011
el4012
es4012
el4014
es4014
el4018
el3433 | 3-phase power measurement terminal 500 v ac, 10 a
the el3433 ethercat power measurement terminal is a further development of the el3403. currents of up to 10 a can be directly measured with the internal current transformers. this way, there are no additional costs for external current transformers. the external bridges 5 & 1&＃39;, 6 & 2&＃39; and 7 & 3&＃39; are already pre-wired. as a result, it is possible to directly connect the supply voltage (5&＃39;, 6&＃39; and 7&＃39;) and the consumer (1, 2 and 3). the el3433 can deal with simple grid analysis up to the 21st harmonic analysis. like all measured terminal data, the harmonic content can be read via the process data.
the el3433 power measurement terminal has neutral conductor current measurement as standard since the 3rd quarter of 2015. at no additional cost to the end user, the terminal features a shunt between pin 4 and pin 8, in order to enable direct neutral conductor analysis.
technical datael3433
number of inputs 4 x current, 3 x voltage
technology 3-phase power measurement for alternating voltages
oversampling factor –
distributed clocks –
conversion time mains-synchronous
measured values current (i1, i2, i3, in), voltage, effective power, reactive power, apparent power, energy, cos φ, frequency, harmonic
measuring voltage max. 500 v ac 3~ (ulx-n: max. 288 v ac)
measuring current max. 10 a (ac)
resolution 1 μa, 0.1 mv, 10 mw
measuring error 0.5 % relative to full scale value (u/i), 1 % calculated value
electrical isolation 4500 v
current consumption power contacts –
current consumption e-bus typ. 200 ma
special features direct current measurement, current measurement,harmonic analysis, single-phase operation also possible
weight approx. 100 g
operating/storage temperature -25…+60 °c/-40…+85 °c
relative humidity 95 %, no condensation
vibration/shock resistance conforms to en 60068-2-6/en 60068-2-27
emc immunity/emission conforms to en 61000-6-2/en 61000-6-4
protect. class/installation pos. ip 20/variable
approvals ce, ul
脉波列+方向讯号 1→正转脉波列+反转脉波列 0,2→ab 相 0→有效 1→无效 设定要反馈到控制器的编码器每圈所输出的脉冲个数 0→b 相不反 1→b 相反 (此值根据实际情况计算所得) (此值根据实际情况计算所得) (此值根据实际情况计算所得)pr43 pr44 pr46 pr48 pr4a pr4b pr10 pr11 pr12 pr21 pr221*50 *60 *15 01/s（此值先为出厂值） hz（此值先为出厂值） ms（此值先为出厂值） 0→不用 1→使用(很少起伏) 2→使用(起伏较慢) 3→使用(快) 设定用于实时自动增益调整的机械刚性调用33 syntec 伺服连接与设定手册 3 松下 a5：34 syntec 伺服连接与设定手册参数仅供参考参数 pr0.00 名称 旋转方向设定 参数范围 0～1 设定值 1 参数意义 0：正向指令时，电机旋转方向 为cw方向 1：正向指令时，电机旋转方向 为ccw方向 0：位置 1：速度 2：转矩 0：无效 1：标准 此值根据实际情况设定 此值根据实际情况设定 0 0：光电耦合器输入 1：长线驱动器专用输入 如果出现转动手轮脉冲发出在 向上增加，回收在减小的情况 要调整此参数 0,2：ab相 1：正负相脉冲 3：脉冲序列+符号 设为 0 时， pr0.09 ， pr0.10 参数 有效 此值根据实际情况设定 此值根据实际情况设定 1~262144 0~262144 2500 0 此值根据实际情况设定 此值根据实际情况设定
上海勇控自动化设备有限公司
曾先生
15988242149
上海 上海 青浦区 上海宝山工业园区