产品详细说明
 
category
类别
trade-
mark
牌号
equivalent to china standard
相当国标
characteristics & application
特性和用途
equivalent to aws
相当aws
 
hard-surfacing
硬
面
 
堆
 
焊
 
d 667
edzcr-b-15
hrc≥48. resistance to wear, gas corrosion and oxidation. hardfacing of blast furnace hopper and cracker part.
hrc≥48，耐磨、耐气蚀、抗氧化。堆焊高炉料钟、破碎机件
d 802
edcocr-a-03
hrc38-47. resistance to heat, wear and corrosion. hardfacing of high temperature part such as the edge of thermo-cutter.
hrc38-47，耐热、耐蚀、耐磨。堆焊高温工件如热剪切刀刃
ecocr-a
d 812
edcocr-b-03
hrc45-50. resistance to heat, wear and corrosion. hardfacing of high temperature part such as internal-combustion engine valve.
hrc45-50，耐热、耐蚀、耐磨。堆焊高温工件如内燃机阀
ecocr-b
d 822
hrc≥53. resistance to wear and heat, bad shock resistance. hardfacing of rotating blade wheel of boiler.
hrc≥53，耐热、耐磨，但抗冲击性差。堆焊锅炉旋转叶轮
d 832
edcocr-c-03
hrc≥50. wear and heat resistance. hardfacing of high temperature part such as hot-rolling guided way.
hrc≥50，耐热、耐磨。堆焊高温工件如热轧导轨
ecocr-c
d 842
edcocr-d-03
hrc28-38. corrosion and thermo-fatigue resistance, work harding. hardfacing of hot forging die.
hrc28-38，耐蚀、抗热疲劳，具有加工硬化性。堆焊热锻模
 
cast iron
 
铸
 
铁
z 308
ezni
pure nickel, excellent general properties. used to weld thin cast iron part and repair welding machined surface, such as guided way of machine tool.
纯镍，综合性能好。铸铁薄件及加工面补焊用，如机床导卫
eni-cl
z 408
eznife
iron nickel, high strength and excellent ductility. repair welding of important gray cast iron and nodular cast iron, such as cylinder cap.
镍铁，强度高、塑性好。重要灰铸铁及球铁焊补用，如汽缸盖
enife-cl
z 508
eznicu-1
copper nickel, good machinability and bad crack resistance. repair welding of sand hole and gray cast iron machined surface subject to no load.
镍铜，易加工，但抗裂性较差。不受力的灰铸铁加工面及砂眼补焊
enicu-b
 
copper alloys
 
铜
 
合
 
金
cu 107
ecu
red copper, atmosphere and sea water corrosion and excellent electric conductivity. welding of red copper such as electrical copper row.
紫铜，耐大气，海水腐蚀，导电性好。紫铜焊接用，如导电铜排
ecu
cu 207
ecusi
silicon bronze, corrosion resistance and high strength. welding of copper, silicon bronze and brass.
硅青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用
ecusi
cu 227
ecusnb
tin phosphor bronze, corrosion resistance and high strength. welding of copper, silicon bronze and brass.
锡磷青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用
ecusn-c
cu 237
ecual
aluminum bronze, wear and corrosion and high strength. welding or surfacing of copper alloys.
铝青铜，耐磨、耐蚀，强度高。铜合金焊接或堆焊用
ecual-a2
 
aluminum alloys
 
铝
合
金
al 109
tal
pure aluminum, excellent corrosion resistance and middle strength. welding of pure aluminum.
纯铝，耐蚀性好，但强度不高，纯铝焊接用
e1100
al 209
talsi
silicon aluminum, good crack resistance and wide range of usage. welding of aluminum alloys other than aluminum magnesium alloys.
铝硅，抗裂性好，通用性大。铝合金焊接用，不宜焊接铝镁合金
e4043
al 309
tamn
manganese aluminum, corrosion resistance and high strength. welding of aluminum alloys.
铝锰，强度高，耐蚀。铝合金焊接用
e3003
 
nickel alloys
镍合金
ni 102
eni-1
pure nickel. welding and surfacing of nickel and nickel to steel.
纯镍，用于镍、镍与钢的焊接与堆焊
eni-1
ni 207
enicu-7
copper nickel. welding and surfacing of copper nickel and copper nickel to steel.
镍铜，用于镍铜、镍铜与钢的焊接与堆焊
enicu-7
 
category
类别
trade
mark
牌号
chemical compostttion
主要成份(%)
characteristics & application
特性和用途
equivalent to aws
相当aws
 
hardfacing
 
硬
 
面
 
堆
 
焊
s 101
c3 cr28 ni4
si3.5 fe rem.
hrc48-54. resistance to wear, gas corrosion and oxidation. hardfacing of bucket tooth and case pump.
hrc48-54，耐磨、耐气蚀、抗氧化。堆焊铲斗齿，泵套
s 111
c1 cr29 w5
co rem.
hrc38-47. resistance to wear and corrosion at high-temperature. hardfacing of high temperature and pressure valve.
hrc38-47，高温下耐磨、耐蚀。堆焊高温高压阀门
ecocr-a
s 112
c1.5 cr29 w8
co rem.
hrc45-50. resistance to wear and corrosion at high-temperature. hardfacing of valve and hot-rolling pass.
hrc45-50，高温下耐磨、耐蚀。堆焊阀门，热轧孔型
ecocr-b
s 113
c2.5 cr30 w17
co rem.
hrc≥55. wear and heat resistance at high temperature, bad shock resistance. hardfacing of screw charging carriage.
hrc≥55，高温下耐磨、耐热，但抗冲击性差。堆焊螺旋送料机用
s 114
c2.5 cr30 w12
co rem.
hrc≥53. wear and heat resistance at high temperature, bad shock resistance. hardfacing of three-cone bit.
hrc≥53，高温下耐磨、耐热，但抗冲击较差。堆焊牙轮钻头
ecocr-c
 
copper
alloys
 
 
铜
 
合
 
金
s 201
sn1 si0.3mn0.3
cu rem.
good mechanical properties and crack resistance. gas welding and argon arc welding of red copper.
机械性能好，抗裂性好。紫铜气焊及氩弧焊用
ercu
s 211
si3 mn1
cu rem.
good mechanical properties. argon arc welding of copper alloys and mig brazing of steel.
机械性能好，铜合金氩弧焊及钢的mig钎焊用
ercusi-al
s 212
sn5 cu rem.
wear resistance. argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用
ercusn-a
s 213
sn8 cu rem.
wear resistance. argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用
ercusn-c
s 214
al7.5 cu rem.
wear and corrosion resistance. argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用
ercual-a1
s 215
al9 cu rem.
wear and corrosion resistance. argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用
ercual-a2
s 221
cu60 sn1 si0.3
zn rem.
melting point is about 890℃. gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约890℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
s 221f
cu60 sn1 si 0.3
zn rem.
s221 welding rod coated with flux.
外涂焊剂的s221焊丝
s 222
cu58sn0.9si0.1
fe0.8 zn rem.
melting point is about 880℃. gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
rbcuzn-c
s 222f
cu58sn0.9si0.1
fe0.8 zn rem.
s222 welding rod coated with flux.
外涂焊剂的s222焊丝
rbcuzn-c
s 223
cu59 sn0.6
zn rem.
melting point is about 900℃. braze welding of copper, steel and cast iron.
熔点约900℃。铜、钢、铸铁钎焊用
rbcuzn-a
s 224
cu62 si0.5
zn rem.
melting point is about 905℃. gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约905℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
copper
alloys
铜
 
合
 
金
s 225
cu48 ni10
zn rem.
melting point is about 935℃and high strength. braze welding of steel, nickel and carbide alloys.
熔点约935℃。高强度,钎焊钢、镍及硬质合金用
rbcuzn-d
s 225f
cu48 ni10
zn rem.
s225 welding rod coated with flux.
外涂焊剂的s225焊丝
rbcuzn-d
s 226
cu60 sn0.3
si0.2 zn rem.
melting point is about 900℃. gas welding of brass, also braze welding of copper, steel and cast iron.
熔点约900℃。黄铜气焊用，也可钎焊铜、钢、铸铁
s 227
cu58sn0.9ni0.5
si0.1 fe0.8
zn rem.
melting point is about 880℃. gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
rbcuzn-b
s 229
cu55 ni6 mn4
zn余
melting point is about 920℃, high strength. braze welding of steel, nickel and hard carbide.
熔点约920℃。高强度,钎焊钢、镍及硬质合金用
aluminum alloys
 
铝
 
合
 
金
s 301
al≥99.5
good ductility and corrosion resistance. gas welding and argon arc welding of pure aluminum.
塑性好、耐蚀。纯铝气焊、氩弧焊用
er1100
s 311
si5 al rem.
corrosion resistance, wide range of usage. gas welding and argon arc welding of aluminum alloys other than high magnesium alloys.
抗裂性好，通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金
er4043
s 321
mn1.3 al rem.
good corrosion resistance, weldability and ductility. gas welding and argon arc welding of aluminum alloys.
良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用
s 331
mg5 mn0.4
al rem.
corrosion resistance and high strength. argon arc welding of aluminum alloys.
耐蚀，强度高。铝合金氩弧焊用
er5183
斯米克钎焊料分别有：（铜锌钎焊料），（铜磷银基钎焊料），（铝基钎焊料），（锡铅钎焊料），（镍基钎焊料).简介如下：
 
category
类别
trade-mark
牌号
specification
规格
melting
point
熔点(℃)
chemical
compostttion
主要成份(%)
application
用途
 
equivalent
to aws
相当aws
 
copper
zinc
铜锌
l103
wire & rod
丝
885-888
cu54 zn rem.
brazing of copper, bronze and steel, subjected to low load.
钎焊铜、青铜和钢等受力不大工件
l104
foil
箔
890-930
cu57 mn2
co2 zn rem.
brazing of carbide cutting tool.
钎焊硬质合金刀具
 
copper
phosphorus
 
铜磷
l201
cast rod, wire & rod, powder
铸条、丝、粉
710-800
p7 cu rem.
brazing of copper and copper alloys.
钎焊铜及铜合金
bcup-2
l204
cast rod, wire
铸条、丝
640-815
p5 ag15
cu rem.
brazing of copper, copper alloys, silver and molybdenum etc.
钎焊铜及铜合金、银、钼等金属。
bcup-5
l205
cast rod, wire & rod, powder
铸条、丝、箔
640-800
p6 ag5
cu rem.
brazing of copper and copper alloys.
钎焊铜及铜合金
bcup-3
l207
cast rod, wire & rod
铸条、丝
640-770
p7 ag5
cu rem.
brazing of copper and copper alloys.
钎焊铜及铜合金
bcup-7
l209
cast rod, wire
铸条、丝
684-710
p7 ag2
cu rem.
brazing of copper and copper alloys.
钎焊铜及铜合金。
bcup-6
 
silver
base
 
银基
l302
wire & rod
丝
745-775
ag25 cu40
zn rem.
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
l303
wire & rod
丝
660-725
ag45 cu30
zn余
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
bag-5
l303f
flux coated rod
涂药丝
660-725
ag45 cu30
zn rem.
l303 coated with flux, the same application as l303.
外涂钎剂的l303，用途与l303相同
bag-5
l304
foil
箔
690-775
ag50 cu34
zn rem.
brazing of copper, copper alloys and steel etc.
钎焊铜及铜合金、钢等
bag-6
l308
wire & rod
丝
779-780
ag72 cu rem.
brazing of copper and nickel under vacuum or reducing protective atmosphere.
铜和镍的真空或还原保护气氛钎焊
bag-8
l312
wire & rod
丝
595-605
ag40.cu.zn.cd
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
l313
wire & rod
丝
625-635
ag50.cu.zn.cd
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
bag-1a
l321
wire & rod
丝
615-650
ag56.cu.zn.sn
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
bag-7
l323
wire & rod
丝
665-755
ag30.cu.zn.sn
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
l325
wire & rod
丝
645-685
ag45.cu.zn.sn
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
bag-36
l326
wire & rod
丝
650-720
ag38.cu.zn.sn
brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
bag-34
 
aluminum base
铝基
l400
cast rod, wire & rod
铸条、丝
577-582
si11.5
al rem.
brazing of aluminum and aluminum alloys.
铝及铝合金的钎焊
balsi-4
l401
cast rod
铸条
525-535
si5 cu28
al rem.
brazing of aluminum and aluminum alloys.
铝及铝合金的钎焊
 
tin lead
锡铅
l600
wire & rod
丝
183-185
sn60 sb≤0.8
pb rem.
soldering of fusible metals and heat-treated part.
易熔金属及热处理件的钎焊
60sn
l601
wire & rod
丝
183-227
sn18 sb2
pb rem.
soldering of copper, copper alloys and galvanized iron plain sheet.
铜及铜合金、镀锌铁皮的钎焊。
18sn
l602
wire & rod
丝
183-256
sn30 sb2
pb rem.
soldering of copper, brass, copper alloys and galvanized iron plain sheet.
铜、黄铜、铁、镀锌铁皮的钎焊
30sn
l603
wire & rod
丝
183-235
sn40 sb2
pb rem.
soldering of copper, copper alloys, steel and zinc parts.
铜及铜合金、钢、锌制零件的钎焊
40sn
l604
wire & rod
丝
183-222
sn90 sb≤0.15
pb rem.
soldering of copper and steel for food and medicine field.
食品、医疗所需铜、钢等金属的钎焊
90sn
l605
wire & rod
丝
232-240
ag5 sn95
soldering of copper and steel for electrical and food field.
电器、食品所需铜、钢等金属的钎焊
l608
wire & rod
丝
295-305
sn5.5 ag2.5
pb rem.
soldering of copper, copper alloys, steel and stainless steel.
铜及铜合金、钢及不锈钢的钎焊
nickel base
镍基
l702
powder
粉
970-1000
cr7 b3 si4
ni rem.
brazing of stainless steel under vacuum or protective atmosphere.
不锈钢真空或保护气氛钎焊
bni-2
 
category
类别
trade-mark
牌号
product name
名称
characteristics & application
特性和用途
gas
welding
气焊
cj301
copper gas welding flux
铜气焊熔剂
melting point is about 650℃, flux for gas welding and brazing of copper and copper alloys.
熔点约650℃，铜及铜合金气焊或钎焊的助熔剂
cj401
aluminum gas welding flux
铝气焊熔剂
melting point is about 560℃, flux for gas welding of aluminum and aluminum alloys.
熔点约560℃，铝及铝合金气焊的助熔剂
 
silver
brazing
银钎焊
qj101
silver brazing flux
银钎焊熔剂
brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃.
在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
qj102
silver brazing flux
银钎焊熔剂
brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
qj102a
silver brazing flux
银钎焊熔剂
brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. non agglomeration.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢。不易结块
qj112
silver brazing paste flux
膏状银钎焊熔剂
brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
qj103
silver brazing flux
银钎焊熔剂
brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃.
在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
aluminum brazing
铝钎焊
qj201
aluminum brazing flux
铝钎焊熔剂
brazing flux of aluminum and aluminum alloys within 450-620℃.
在450-620℃范围钎焊铝及铝合金的助熔剂
qj207
aluminum brazing flux
铝钎焊熔剂
brazing flux of aluminum and aluminum alloys within 560-620℃.
在560-620℃范围钎焊铝及铝合金的助熔剂